ROADSAFE MIDDLE BLACK SPEED BUMP MALAYSIA
ROADSAFE MIDDLE YELLOW SPEED HUMP MALAYSIA
ROADSAFE END CAP MALAYSIA
ROADSAFE END CAP YELLOW
ROADSAFE MIDDLE SPEED BUMP FULL MALAYSIA
ROADSAFE END CAP MARK MALAYSIA
ROADSAFE END CAP LOGO MALAYSIA
ROADSAFE END CAP END CAP TRADEMARK MALAYSIA
ROADSAFE END CAP TRADEMARK MALAYSIA
ROADSAFE AUTHENTIC END CAP MALAYSIA
Copyright © GSE ONLINE SDN BHD ( 1116968-P ) ALL RIGHTS RESERVED


A) Product Name
100% homogeneous Vulcanised EPDM RUBBER SPEED BUMP with locks to prevent dislocation after installation. ( With Cat Eyes Reflective Glass )

B) Brand  
RUDSAF ™  ( ROADSAFE ),

MADE IN MALAYSIA

C) Raw Material 

Made of 100% homogeneous Vulcanised EPDM Rubber
( No Recycled / Reclaimed Rubber ) & moulded with around 3mm of EPDM Yellow wear layer for the Yellow Part for better visibility. 


​​D) Purpose
1) Control vehicle speeds to promote pedestrian safety 

2) Reduce the risk of accidents in parking areas and residential streets

E) Scope

Speed bumps are more aggressive traffic calming options and are helpful in places where pedestrians and cars share space closely, like parking lots and driveways.

F) Characteristics
Our RUDSAF  meets Australian/New Zealand Standards of “AS/NZS2890.1:2004 Parking Facilities” it determines four main types of criteria for speed Bumps.

 Why AS/NZS2890.1:2004 ParkingFacilities?
 AS/NZS2890.1:2004 is an Australian/New Zealand Standard that guides specific minimum requirements for the design and layout of off-street car parking.

 ​​The content within  AS/NZS2890.1:2004 can be pretty comprehensive as our reference.


  Bumps that comply with standards are determined by height, cross-section, markings, and angles below.


Criteria 1 )
Height: Must be between 25 to 75mm.

Criteria 2 )
Cross Section: Must be flat on top of around 100mm ~ 150mm, and Shape cannot in parabolic or peaked.

Criteria 3 )
Ramp Angle: Must have a ramp angle of 2:1

​​
Criteria 4 )
Markings: Must have alternating yellow stripes 250mm wide.

RUDSAF EPDM RUBBER SPEED BUMPS
          ​
Why We Choose Homogeneous EPDM Rubber& What are the Benefits of using EPDM Rubber?
          ​
i) Homogeneous EPDM Rubber will compress under high impact better than recycled/ reclaimed rubber.
            ​
ii) Resistance to UV exposure, ozone, ageing, weathering and many chemicals - excellent for outdoor applications, Do not use EPDM rubber if continual contact with petroleum-based products is required.
            ​
iii) Stability in high and low temperatures - EPDM material can be used in severe environmental conditions, and the withstand temperature range from -20⁰F to +300⁰F (-29⁰C to 150⁰C)
            ​
iv) Low electrical conductivity
              ​
v) Steam and water-resistant

            ​
vi) Properties allow it to be widely used and highly​versatile, can be applied successfully in many situations
              ​
vii) Used in the proper environment, the parts will work well and last long without breaking down, brittle, etc.


 
G) SPECIFICATIONS
1) Manufacture from High-Density 100%Homogeneous EPDM Rubber with cat’s eye and “ LOCK “ features to prevent dislocation after installation, an additional advantage for uneven/soft Asphalt ( Tar ) road surface.

​​2) Available in Black &Yellow combination for greater visibility

3) Anti-skid surface with flattop of 110mm Width as defined under
AS/NZS2890.1:2004 Parking Facilities of Criteria 2.

​4) All units can purchase separately

​​5) Sizes :-
​i) Model : RSBB250X310, 100% BLACK EPDM Rubber, Middle Black Speed Bumps with Lock,~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc
            ​
ii) Model: RSBY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, Middle Yellow Speed Bumps with Lock,~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc

​​iii) Model : RECB250X310, 100% BLACK EPDM Rubber, End Cap Black Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc
            ​
iv ) Model: RECY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, End Cap Yellow Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc

 RECOMMENDED Lag bolts:- 

A) For concrete, use ½-inch diameter lag bolts and 4 to 5-inch in length


        ​​​​​​​
​Disclaimer :
    ​* Note : Users need to evaluate suitability for their industries use ( applications ) before placing order from us .

​HIGH QUALITY RUDSAF
      ​100% EPDM RUBBER
      ​ ​SPEED BUMP

RUBBER SPEED HUMP



 
 
 
 
 
 
GSE ONLINE SDN. BHD. rudsaf speed bump Malaysia 25mm 100mm h2h speed hump yellow stripe Malaysia
Criteria 1 )
Criteria 2 )
Criteria 3 )
Criteria 4 )
AS/NZS2890.1:2004
Roadsafe Traffic Yellow End Cap Malaysia Roadsafe speed hump Black Middle Black Malaysia Roadsafe speed hump Middle Yellow Malaysia Roadsafe Traffic Black End Cap Malaysia
Advantages :-

​(1) DIS-LOCATION PREVENTION
Speed bump dislocation Malaysia Speed bump Malaysia after assembling Speed bump Malaysia before assembling
BEFORE ASSEMBLING
AFTER ASSEMBLING
GSE ONLINE SDN. BHD. GSE ONLINE SDN. BHD. BUY NOW